ガス発生剤による超塑性5083アルミニウム合金の新しいバルジ成形法

• 資料種別: 記事
• タイトル: ガス発生剤による超塑性5083アルミニウム合金の新しいバルジ成形法
• 著者・編者: 大澤 泰明; 石田 賢司
• 著者標目: 大澤 泰明; 石田 賢司
• タイトル（掲載誌）: 軽金属 = Journal of the Japan Institute of Light Metals
• 巻号年月日等（掲載誌）: 54(8) (通号 526) 2004.8
• 掲載巻: 54
• 掲載号: 8
• 掲載通号: 526
• 掲載ページ: 323～327
• 掲載年月日（W3CDTF）: 2004-08
• ISSN（掲載誌）: 0451-5994
• ISSN-L（掲載誌）: 0451-5994
• 出版事項（掲載誌）: 東京 : 軽金属学会
• 出版地（国名コード）: JP
• 本文の言語コード: jpn
• 件名標目: sheet metal forming; 5083 aluminum alloy; bulge forming; superplasticity; gas generant
• NDLC: ZP41
• 対象利用者: 一般
• 所蔵機関: 国立国会図書館
• 請求記号: Z17-284
• 連携機関・データベース: 国立国会図書館 : 国立国会図書館雑誌記事索引; https://ndlsearch.ndl.go.jp
• 書誌ID（NDLBibID）: 7077785; http://id.ndl.go.jp/bib/7077785
• 整理区分コード: 632

• 要約等: Gas blow forming originally developed to thermoplastics has been revised and applied to superplastic alloy sheets. It involves, however, low production rate, high cost for forming tools and poor working environment due to heating. Instead of using inert gas or air blowing, dilatational work of inert gases during heating was inspired by authors as a kind of pressure source. Several gas generants being used in forming foamed plastics or metals and air bag in car seem to be available for the purpose. A few of gas generants in form of powder were tentatively selected and supplied for experiments here. Conventional gas blow forming and proposed method with using these gas generants were compared with regard to formability and cavitation. Experimental results on superplastic aluminum sheets obviously demonstrate a feasibility of practical use of it in engineering application.
• DOI: 10.2464/jilm.54.323
• オンライン閲覧公開範囲: インターネット公開
• 連携機関・データベース: 科学技術振興機構 : J-STAGE; http://www.jstage.jst.go.jp

• 要約等: Gas blow forming originally developed to thermoplastics has been revised and applied to superplastic alloy sheets. It involves, however, low production rate, high cost for forming tools and poor working environment due to heating. Instead of using inert gas or air blowing, dilatational work of inert gases during heating was inspired by authors as a kind of pressure source. Several gas generants being used in forming foamed plastics or metals and air bag in car seem to be available for the purpose. A few of gas generants in form of powder were tentatively selected and supplied for experiments here. Conventional gas blow forming and proposed method with using these gas generants were compared with regard to formability and cavitation. Experimental results on superplastic aluminum sheets obviously demonstrate a feasibility of practical use of it in engineering application.
• DOI: 10.2464/jilm.54.323; https://doi.org/10.2464/jilm.54.323
• 関連情報（URI）: http://id.ndl.go.jp/bib/7077785; https://ndlsearch.ndl.go.jp/books/R000000004-I7077785
• 参照: Mg-Al-Zn-Ca系ポーラスマグネシウム合金の室温圧縮特性(<小特集>M&P2009機械材料・材料加工部門技術講演会); https://cir.nii.ac.jp/crid/1390001204478368000
• 参照: Influence of hydrostatic pressure and multiaxial straining on cavitation in a superplastic aluminum alloy; https://cir.nii.ac.jp/crid/1363670320518965248; Reversal of regiospecificity in ground-state vs. excited-state cycloadditions; https://cir.nii.ac.jp/crid/1364233270457790720
• 連携機関・データベース: 国立情報学研究所 : CiNii Research; https://cir.nii.ac.jp/
• 提供元機関・データベース: Japan Link Center; https://japanlinkcenter.org/top; 雑誌記事索引データベース; https://ndlsearch.ndl.go.jp; Crossref; https://www.crossref.org; CiNii Articles
• 書誌ID（NDLBibID）: 7077785; http://id.ndl.go.jp/bib/7077785
• NII論文ID: 10013536870