Studies on Aero-Thermal Performances of Leakage Flows lnjection from the Endwall Slot in Linear Cascade of High-Pressure Turbine

• 資料種別: 博士論文
• タイトル: Studies on Aero-Thermal Performances of Leakage Flows lnjection from the Endwall Slot in Linear Cascade of High-Pressure Turbine
• 著者・編者: Wan, Aizon Bin W Ghopa
• 出版事項: 岩手大学
• 出版年月日等: 2013
• 出版年（W3CDTF）: 2013
• 並列タイトル等: エンドウォールスロットからの漏れ流れを伴う高圧タービン直線翼列の熱流体的特性に関する研究
• 授与機関名: 岩手大学
• 授与年月日: 2013-09-25
• 授与年月日（W3CDTF）: 2013-09-25
• 報告番号: 甲第240号
• 学位: 博士 (工学)
• 博論授与番号: 甲第240号
• 本文の言語コード: eng
• 件名標目: Turbomachinery; secondary flow; endwall film cooling; leakage flow; purge flow; heat transfer; high-pressure turbine; liquid crystal; transient method; pressure loss; slot orientation; slot position
• 一般注記: Present studies focus on thermal and aerodynamics investigations of leakage flow injection through a slot which is located at upstream of blade leading edge. In the real gas turbine, this slot is actually the gap between the combustor and turbine endwall as for the maintenance works consideration. However, the slot induced to the leakage phenomenon caused by the bypassed air that coming from the compressor side for turbine cooling purposes. Gas turbine manufactures intended to minimize these kinds of leakages in maintaining the aerodynamics performance of the turbine cascade. However, previous researchers found that the leakages could be used to protect the endwall surfaces from the hot gas since it could not be completely prevented. Thus, present study investigated the potential of leakage flows as a function of film cooling. Chapter 1 gives some introduction on present works about the need of film cooling to protect the wall surfaces. Several related studies by previous researchers are also explained. Chapter 2 explained the details of methodologies used in present studies. A leakage flow with 90° of injection angle was considered as for the baseline configuration. Liquid crystal was used for the time-varying endwall temperature measurement. The transient method was applied to determine the film cooling effectiveness, η and the heat transfer coefficient, h for the thermal performance evaluations. The details of the aerodynamics performances was revealed by conducting 5-holes Pitot tube measurement at blade downstream plane (1.25Cax) and the total pressure loss coefficient, Cpt as well as the flow vorticity, ζ contours were plotted. Furthermore, the effects of the leakage flow with the mainstream consist of complex secondary flows structures also have been revealed by numerical investigation. In present study, the flow is analyzed by using the three-dimensional, steady Reynolds-averaged Navier-Stokes (RANS) equations by conducting Shear Stress Transport, SST turbulence model. The leakage was injected with a various amount (which is described by mass flow ratio, MFR) to observe theηperformance at different injection cases. Chapter 3 provided details discussions on the aero and thermal performances of the leakage injection. Both experimental and numerical presented the performance ofηincreased when the injection amount increases. SST turbulence model captured the presence of the separation flow that caused the lower h region which also captured by the experimental. As for the aerodynamics performance, Cpt was increased after the introduction of leakage injection and indicated the increase trend when the MFR was being increased. Leakage flows were prevented to be injected into high pressure region thus they tended to move towards lower pressure region which is between two stagnation regions. As a result, a newly generated vortex core was predicted. This accumulated vortex core (AFV) is considered to contribute to the additional losses at blade downstream. Chapter 4 presents the numerical investigation on the modification of slot configurations such as positions and orientations. The leakages flow by shallower injection angle, βtowards mainstream was predicted to reduce the strength of the passage vortex thus increase the aerodynamics performance particularly at higher injection cases. Additionally, ηalso obviously increased by the slot orientation. To move away the slot from the blade LE was predicted to increase both aero and thermal performance. The leakage flow could laterally be penetrated to the mainstream and stayed closer on endwall surfaces. This is due to the fewer blockages influenced by the stagnation region since the slot located far away from the blade LE. In contrast, move the slot closer towards blade LE just increased the Cpt Furthermore, locate the slot closer to blade LE could not increase the protection layer except the level of η. Finally, Chapter 5 highlights the important points to be concluded based on present investigations. The potential of the leakage flows to protect the endwall surfaces has been proven and they were highly influenced by the secondary flows behavior on the endwall region. However, to increase the performance of cooling by increasing the injection amounts unfortunately reduces the aerodynamics performance due to the increase strength of the secondary flow vortices. The leakage flow with a shallow injection angle towards mainstream are predicted to provide a positive trends of cooling performance with a lower aerodynamic losses especially at higher leakage flow injection cases.; 開始ページ : 1; 終了ページ : 154
• DOI: info:doi/10.15113/00010395; https://doi.org/info:doi/10.15113/00010395
• 国立国会図書館永続的識別子: info:ndljp/pid/10370317; https://dl.ndl.go.jp/pid/10370317
• コレクション（共通）: 障害者向け資料
• コレクション（障害者向け資料：レベル1）: テキストデータ
• コレクション（個別）: 国立国会図書館デジタルコレクション > デジタル化資料 > 博士論文; https://dl.ndl.go.jp/collections/A00014
• 収集根拠: 博士論文（自動収集）
• 受理日（W3CDTF）: 2017-07-03T04:10:06+09:00
• 作成日（W3CDTF）: 2016-05-17
• 記録形式（IMT）: application/pdf
• オンライン閲覧公開範囲: 国立国会図書館内限定公開
• デジタル化資料送信: 図書館・個人送信対象外
• 遠隔複写可否（NDL）: 可
• 掲載誌（URI）: http://id.nii.ac.jp/1399/00010395/
• 連携機関・データベース: 国立国会図書館 : 国立国会図書館デジタルコレクション; https://dl.ndl.go.jp