回転水中紡糸法で製造された金属細線の形態に及ぼす製線条件の影響

• 資料種別: 記事
• タイトル: 回転水中紡糸法で製造された金属細線の形態に及ぼす製線条件の影響
• 著者・編者: 高松 洋; 曹曹 奎常; 山城 光 他
• 著者標目: 高松 洋; 曹曹 奎常; 山城 光
• タイトル（掲載誌）: 九州大学機能物質科学研究所報告 / 九州大学機能物質科学研究所 編
• 巻号年月日等（掲載誌）: 9(1) 1995
• 掲載巻: 9
• 掲載号: 1
• 掲載ページ: 13～20
• 掲載年月日（W3CDTF）: 1995
• ISSN（掲載誌）: 0914-3793
• ISSN-L（掲載誌）: 0914-3793
• 出版事項（掲載誌）: 春日 : 九州大学機能物質科学研究所
• 出版地（国名コード）: JP
• 本文の言語コード: jpn
• NDLC: ZM2
• 対象利用者: 一般
• 所蔵機関: 国立国会図書館
• 請求記号: Z14-1380
• 連携機関・データベース: 国立国会図書館 : 国立国会図書館雑誌記事索引; https://ndlsearch.ndl.go.jp
• 書誌ID（NDLBibID）: 3915744; http://id.ndl.go.jp/bib/3915744
• 整理区分コード: 632

• 要約等: Metal wires of Pb, Zn and Fe_<77.5>Si_<7.5>B_<15> were produced by the In-Rotating-Water Spinning Method. The effects on the shape of wire of drum velocity (5.2-8.5m/s), jet ejection velocity (3.5-10.0m/s), incidence angle (30, 45, 60 deg) and nozzle diameter (0.1 and 0.2mm) as well as the kind of metals were examined. Pb showed the best spinnability among the tested metals, although the cross section was relatively flat and marked ripples were formed on the wire surface when the incidence angle and jet velocity were relatively large. A long, straight Fe_<77.5>Si_<7.5>B_<15> wire that had smooth surface and round cross-section was obtained with a 0.2-mm-dia. nozzle when the jet velocity and the drum velocity were almost the same. The Fe_<77.5>Si_<7.5>B_<15> wire produced with a 0.1-mm-dia. nozzle however showed the shape like a string of beads.
• DOI: 10.15017/6667; https://doi.org/10.15017/6667
• オンライン閲覧公開範囲: インターネット公開
• 関連情報: 九州大学機能物質科学研究所報告 || 9(1) || p13-20; The reports of Institute of Advanced Material Study Kyushu University || 9(1) || p13-20; http://www.cm.kyushu-u.ac.jp/
• 連携機関・データベース: 国立情報学研究所 : 学術機関リポジトリデータベース（IRDB）（機関リポジトリ）; https://irdb.nii.ac.jp
• 提供元機関・データベース: 九州大学学術情報リポジトリ(QIR); https://www.lib.kyushu-u.ac.jp/papers

• 要約等: Metal wires of Pb, Zn and Fe_<77.5>Si_<7.5>B_<15> were produced by the In-Rotating-Water Spinning Method. The effects on the shape of wire of drum velocity (5.2-8.5m/s), jet ejection velocity (3.5-10.0m/s), incidence angle (30, 45, 60 deg) and nozzle diameter (0.1 and 0.2mm) as well as the kind of metals were examined. Pb showed the best spinnability among the tested metals, although the cross section was relatively flat and marked ripples were formed on the wire surface when the incidence angle and jet velocity were relatively large. A long, straight Fe_<77.5>Si_<7.5>B_<15> wire that had smooth surface and round cross-section was obtained with a 0.2-mm-dia. nozzle when the jet velocity and the drum velocity were almost the same. The Fe_<77.5>Si_<7.5>B_<15> wire produced with a 0.1-mm-dia. nozzle however showed the shape like a string of beads.
• DOI: 10.15017/6667; https://doi.org/10.15017/6667
• オンライン閲覧公開範囲: インターネット公開
• 関連情報（URI）: https://hdl.handle.net/2324/6667; http://id.ndl.go.jp/bib/3915744; https://ndlsearch.ndl.go.jp/books/R000000004-I3915744
• 連携機関・データベース: 国立情報学研究所 : CiNii Research; https://cir.nii.ac.jp/
• 提供元機関・データベース: Japan Link Center; https://japanlinkcenter.org/top; 学術機関リポジトリデータベース; https://irdb.nii.ac.jp; 雑誌記事索引データベース; https://ndlsearch.ndl.go.jp; CiNii Articles
• 書誌ID（NDLBibID）: 3915744; http://id.ndl.go.jp/bib/3915744
• NII論文ID: 110006177459